Home > PRODUCTS > IT SOLUTIONS > NMEA 0183 & NMEA 2000 Networks > NMEA 0183 Multiplexers >

NDC-4-AIS-USB NMEA0183 Multiplexer

NDC-4-AIS-USB NMEA Multiplexer
 
List Price: $320.00
Our Price: $290.00


Availability:: Usually Ships in 3 to 5 Business Days
Product Code: AS01.00006
Qty:

Description Technical Specs Extended Information
 

Actisense NDC-4-AIS-USB NMEA0183 Multiplexer


Next generation Combiner / Multiplexer that has full isolation on all inputs and all outputs. NDC-4 Base unit pre-configured as AIS Multiplexer, with USB cable.
Using the ISO-Drive Actisense technology, ground loops are now a thing of the past. Can Combine or Autoswitch up to 5 devices, plus filter out any problematic or unwanted NMEA sentences. The NDC-4 has two ISO-Drive outputs which are fully compatible with all standards: NMEA 0183 (RS422), RS485 and PC RS232 ports.
- Full galvanic Opto-isolation on NMEA 0183 inputs
- Full galvanic isolation on NMEA 0183 / ISO-Drive outputs
- Configurable Port Baud rates and priorities
Features & Benefits
  • Completely removes the need for isolated power supplies - as the NDC-4 creates a full 2500v isolation barrier between it's inputs and each of it's ISO-Drive outputs
  • Enables the vessel owner complete access to all NMEA data sources, instead of the standard one device
  • Any problematic or unwanted NMEA sentences can be filtered out / blocked, to help intelligently reduce the NMEA data to a manageable amount and prevent data loops
  • Each NMEA input device is Opto-isolated from all other NMEA device in the system
  • Significant reductions in installation cost (from reduced cable lengths and requiring only one NMEA cable to be routed around the bridge to supply the multiplexed NMEA data
  • New feature: The autoswitching feature of the NSW-1 has now been added to the NDC-4, making it the single most feature rich Multiplexer available in the marine market. The NDC-4 can either operate in 'Combine mode' as before, or the new 'Autoswitch mode' to behave like the original Actisense NSW-1 Autoswitch product.
  • Electrical spike protection is provided as standard on all four input channels using opto-isolators. This protects any connected equipment from most system faults; a particularly valuable benefit as equipment requiring the most data, such as a PC or chart plotter, is often the most expensive to repair or replace.
  • The NDC-4 Data Multiplexer contains intelligent software that manages the multiplexing operation, allowing every input to have a chance of its data reaching the combined NMEA output. Tested up to and beyond a combined 400% loading of the four inputs.
  • 5 Opto-isolated NMEA 0183 data inputs. Full galvanic Opto-isolated differential inputs that fully comply with the NMEA 0183 standard specification. This allows the input to work correctly with long cable runs, and/or in a noisy environment. This also allows the NDC-4 to offer up to 2500v of common mode voltage difference (between its input and outputs). This will prevent any ground loop damage occurring. Inputs 0-3 have independently selectable baud rates of 4800 to 57600 baud; Input 4 is fixed at 4800 baud. (When the USB connection is in use, the number of NMEA opto inputs is reduced to 4).
  • 2 ISO-Drive flexible outputs. The ISO-Drive outputs are fully compatible with the RS422 (NMEA 0183), RS485 and RS232 connections on the NMEA listening device(s) the NDC-4 supplies data to, and offers total galvanic isolation of up to 1500v between the output and ground. The full-differential output ensures better quality communications and lower noise emissions on unshielded twisted pair cabling. Outputs 0 & 1 have independently selectable baud rates of 4800 to 115200 baud.
  • NMEA PC (USB / ISO-Drive) data input. Enables PC software (e.g. chart plotter) to add NMEA sentences to the combined NMEA data output. Perfect for PC chart plotter controlled course steering via the NMEA network.
  • NMEA and PC (USB / ISO-Drive) outputs. Allows any NMEA device and PC to read the combined NMEA data output. Furthermore, special NMEA codes are used to label each NMEA sentence - allowing the NMEA device or PC to determine where all the NMEA information originated from.
  • Powerful processor. An ARM 32-bit microcontroller capable of 40 million instructions per second, and very large NMEA data buffers to allow smoothing of short-term peaks in the NMEA data flow.
  • Flash upgradeable. The hardware's firmware (software) can be easily upgraded as and when necessary.
  • Combine mode: Intelligent software. Filters the valid data from all active inputs, using the configured Inclusion lists, and then combines the remaining data using a simple priority system. Highest priority input (1) has the best chance of its data being added to the output combined NMEA data, and input 4 the lowest chance. This advanced user controlled system only operates as and when it becomes necessary to reduce the NMEA data outputted (triggered by very high loading of the combined NMEA output). The ISO-Drive and / or USB output will always contain all of the NMEA data (due to its higher Baud rate and bandwidth).
  • Autoswitch mode: Intelligent software. Determines the highest priority device with valid data, based on one of three reasons - a failure to send any NMEA data, an invalid NMEA sentence checksum, or if the validity flag(s) contained within the NMEA sentence indicate that this data is not valid and should only be used with caution (for GPS and Depth data). The chosen input's data will be resent out the two ISO-Drive outputs (and USB if available), allowing two different Baud rates to be used (typically 38400 Baud and 4800 Baud).
  • Very low current consumption. Ideal for small vessels with small batteries.
  • Diagnostic tri-colour LED. Indicates current operation mode, volume of data being multiplexed, or if a hardware fault has been detected.
  • IP66/IP68 case and grommet design. A very robust polycarbonate case with a high waterproof certification. The small case size is ideal for space restrictive applications.
  • High quality angled screw terminals. The 'moving cage' type terminals make cable installation a simple and quick operation.


Browse for more products in the same category as this item:

PRODUCTS > IT SOLUTIONS > NMEA 0183 & NMEA 2000 Networks > NMEA 0183 Multiplexers
PRODUCTS > NAVIGATION SOLUTIONS > Interfaces - PC/NMEA
APPLICATIONS > Networking The Ship
PRODUCTS > OTHER SOLUTIONS > Accessories > NMEA Interfaces & Convertors
BRANDS > Actisense